- 您现在的位置：买卖IC网 > Sheet目录470 > MAX11008EVC16 (Maxim Integrated)EVAL KIT MAX11008
Dual RF LDMOS Bias Controller with
Nonvolatile Memory
FIFOEMP is set to 1 when the FIFO is empty. Once data
is placed into the FIFO, FIFOEMP is set to 0.
When in ADC monitoring mode, FIFOOVER is set to 1
when a FIFO overflow occurs. FIFOOVER remains at 1,
even if the FIFO is subsequently read and no longer
full. FIFOOVER is reset by reading the Flag register.
When in LUT streaming mode or message mode, the
FIFO is not permitted to overflow and FIFOOVER then
denotes when the FIFO is full. FIFOOVER is set to 1
Table 19. PGA Calibration Control Register
when the FIFO is full and immediately returns to 0 once
a data word is moved out of the FIFO.
HIGHI_ is set to 1 when the individual channel 1 and
channel 2 current-sense measurements exceed the
individual channel 1 and channel 2 high current thresh-
old and returns to 0 after the Flag register is read.
HIGHI2 is replaced by HIGHT2 when the INTEMP2 bit
is set in the Alarm Hardware Configuration register.
DATA BITS
D[15:3]
BIT NAME
Unused
RESET STATE
X
Unused bits.
FUNCTION
Acquisition/tracking bit. Set to 0 to force the next current-sense calibration
D2
TRACK
0
to run in acquisition mode. Set to 1 to force the next calibration to run in
tracking mode. Set TRACK to 0 the first time through a calibration.
D1
DOCAL
0
Single calibration select bit. Set to 1 perform single or self-timed
calibrations of PGA1 and PGA2. DOCAL resets to 0 after calibration.
Self-timed calibration select bit. Set to 1 to perform calibrations of PGA1
D0
SELFTIME
0
and PGA2 on a self-timed periodic basis (approximately every 13ms).
When set to 0, calibrations only occur when DOCAL is set to 1.
X = Don’t care.
NA = Not applicable.
Table 20. ADC Conversion Register
DATA BITS
D[15:8]
D7
D6
D5
D4
D3
D2
D1
D0
BIT NAME
Unused
CONCONV
ADCIN2
CS2
EXTEMP2
ADCIN1
CS1
EXTEMP1
INTEMP
RESET STATE
X
0
0
0
0
0
0
0
0
FUNCTION
Unused bits.
Continuous conversion select bit. Set to 1 to perform continuous
conversions of the selected channels.
ADCIN2 conversion select bit.
CS2 current-sense conversion select bit.
External temperature sensor 2 conversion select bit.
ADCIN1 conversion select bit.
CS1 current-sense conversion select bit.
External temperature sensor 1 conversion select bit.
Internal temperature sensor conversion select bit.
X = Don’t care.
NA = Not applicable.
______________________________________________________________________________________
61
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX11014BGTM+T
IC RF MESFET AMP 48-TQFN-EP
MAX12000ETB+T
IC AMP GPS FRONT 1575MHZ 10TDFN
MAX12005ETM+T
IC SATELLITE IF SWITCH 48-TQFN
MAX1385BUTM+
IC RF LDMOS BIAS CNTRLR 48-TQFN
MAX1470EUI+T
IC RECEIVER 315MHZ 28-TSSOP
MAX1470EVKIT-315
EVAL KIT FOR MAX1470 315MHZ
MAX1471EVKIT-315
EVAL KIT FOR MAX1471 315MHZ
MAX1472EVKIT-433#
EVAL KIT MAX1472
相关代理商/技术参数
MAX11008EVKIT+
功能描述:放大器 IC 开发工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V
MAX1100CWG
制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX1101
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Single-Chip, 8-Bit CCD Digitizer with Clamp and 6-Bit PGA
MAX11014
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11014_08
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11014BGTM
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11014BGTM+
功能描述:特殊用途放大器 Auto RF MESFET Amp Drain-Current Cntrlr RoHS:否 制造商:Texas Instruments 通道数量:Single 共模抑制比（最小值）: 输入补偿电压: 工作电源电压:3 V to 5.5 V 电源电流:5 mA 最大功率耗散: 最大工作温度:+ 70 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-20 封装:Reel
MAX11014BGTM+T
功能描述:射频放大器 Auto RF MESFET Amp Drain-Current Cntrlr RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel